Simultaneous improvement of thermal conductivity and mechanical properties for mechanically mixed ABS/h-BN composites by using small amounts of hyperbranched polymer additives

Recently, thermal interface materials (TIMs) are in great demands for modern electronics. For mechanically mixed polymer composite TIMs, the thermal conductivity and the mechanical properties are generally lower than expected values due to the sharply increased viscosity and poor filler dispersion. This work shows that addition of a small amount of polyester-based hyperbranched polymer (HBP) avoided the trade-off in mechanically mixed ABS/hexagonal boron nitride (h-BN) composites. After adding 0.5 wt% HBP, the maximum h-BN content in the composites increased from 50 to 60 wt%. The out-of-plane, in-plane thermal conductivity, and tensile strength of ABS/h-BN with 50 wt% h-BN were 0.408, 0.517 W/mK, and 18 MPa, respectively, and were increased to 0.729, 0.847 W/mK, and 32 MPa by adding 0.5 wt% HBP, while 0.972, 1.12 W/mK, and 29.5 MPa were achieved for ABS/h-BN/HBP with 60 wt% h-BN. The morphological and rheological results proved that these enhancements are due to the improved h-BN dispersion by decreasing viscosity of composites during mixing. Theoretical modeling based on the modified effective medium theory confirmed such results and showed that the interfacial thermal resistance also decreased slightly. Thus, this work demonstrates a facile and scalable method for simultaneously improving the thermal conductivity and mechanical properties of thermoplastic-based TIMs.     

浅谈枪支(弹药)库室电子技防测试

一个完整枪支(弹药)库室的安全防范由管理要求、物防要求、技防要求及人防要求完美的结合而成,其中技防要求是需要根据枪支(弹药)库室现场实体情况采取的一项电子技术手段,是起到安全预报警的最佳方式。本文就枪支(弹药)库室安全防范在技防要求方面按现行GA 1016-2012标准在检测中存在的问题做一些探讨、建议,以期为需要枪支(弹药)库室的建设单位、施工单位提供参考。     

某两自由度弹药提升装置的建模、实验及仿真研究

弹药自动装填系统的研究已经成为火炮武器平台中机械系统设计的关键和难点,基于一种两自由度弹药提升装置,并根据该装置的工作原理构造数学模型,搭建实验平台,建立PID控制回路,同时创建该模型的虚拟样机模型,使用动力学仿真软件Recurdyn和Matlab/Simulink进行联合仿真,并通过实验与仿真的数据进行对比,验证该装置的可行性和所采用控制的有效性。     

Systematic packaging design tools integrating functional and environmental consequences on product life cycle: Case studies on laundry detergent and milk

This study presents systematic packaging design tools integrating functional and environmental consequences on product life cycle. To design packaging for sustainability, the trade-offs between functional and environmental aspects of packaging throughout the product life cycle should be considered. However, it is difficult for packaging designers to understand the overall trade-offs because the extent of the design consequences on the entire life cycle of packaging and its contents is unclear. We developed two tools for packaging design: the Life Cycle Association Matrix (LCAM) and the Function Network Diagram (FND). The following three steps, based on literature reviews and interviews with industrial experts, were applied. Firstly, we listed the product functions and design variables related to the functions as the attributes allocated to the product life cycle. Secondly, the attributes were connected appropriately based on causal relationships. Lastly, we identified the factors to support decision making in the packaging design procedure. As a result, the LCAM depicts the design consequences on the life cycle, and the FND determines the stakeholders affected by the design consequences. Two case studies were demonstrated to analyze the trade-offs by using our tools. In the case studies, a liquid laundry detergent bottle and a milk carton were redesigned. The tools identified the design consequences and stakeholders affected by the redesign of the usability and protective function for the detergent and milk cases, respectively. The results showed the significance of understanding the design consequences on the product life cycle by integrating the functional and environmental aspects.     

Cellulose nanoparticles synthesised from potato peel for the development of active packaging film for enhancement of shelf life of raw prawns (Penaeus monodon) during frozen storage

In this study, the cellulose nanoparticles (CNP) isolated from potato peel were used for reinforcement of polyvinyl alcohol (PVA)-based active packaging film. The above film was used to pack the raw prawns (Penaeus monodon) at −20 °C, and the colour change, protein content, TVB-N, TMA and microbial analysis were done at regular interval for prawns stored in CNP-PVA active packaging film. A significant difference was observed in the quality of prawns stored in potato CNP-PVA film compared with prawns packed and stored in polyethylene film. The newly designed active packaging with CNP and fennel seed oil enhanced the shelf life of prawns up to two months for both HOSO (head on shell on) prawn and PD (peeled and deveined) prawn. Hence, the study recommends the potato peel CNP-PVA film with fennel seed oil as better choice to extend the shelf life of the prawns during storage compared with polyethylene packaging.     

冷链条件下气调包装酱卤鸭肉制品货架期预测模型的建立

目的 以气调包装酱卤鸭肉制品为研究对象,在冷链温度范围内建立一套准确、高效的货架期预测模型。方法 利用选择性培养基测定不同温度下产品各微生物数量,确定4~25℃条件下产品优势腐败菌。对乳酸菌数量与感官评定值进行了回归分析确定最小腐败量Ns。分别采用修正的Gompertz方程和平方根方程建立一、二级模型,并通过预测值与实测值对比验证模型的可靠性。结果 确定了4~25℃条件下产品优势腐败菌为乳酸菌,最小腐败量Ns=6.14(lg(cfu /g))。一、二级模型拟合度均良好,三种温度下模型预测值与实际值间的差异均在30％左右,波动幅度在10%以内。结论 实现了对4~25℃内任何时间点产品剩余货架期的预测,为冷链条件下气调包装酱卤鸭肉制品品质的变化提供了理论指导。     

Synergistic effects of modified TiO2/multifunctionalized graphene oxide nanosheets as functional hybrid nanofiller in enhancing the interface compatibility of PLA/starch nanocomposites

The aim of this study is to investigate the synergistic effects of modified TiO₂/multifunctionalized graphene oxide nanosheets at different ratios on the interface compatibility between starch and poly(lactic acid) (PLA). To this end, silanylated nano-TiO₂ (MTiO₂, 1 and 2%) and alkylated maleic anhydride grafted graphene oxide (f-GO, 0.1, 0.2, and 0.4%) at different combinations are blended with the PLA-starch composites using solution blending technique. Then, the synergistic effects of MTiO₂ and f-GO on PLA/starch matrix are investigated in terms of the morphology, crystallinity, structural characterization, thermal stability, dynamic mechanical, and antiaging properties, and the related mechanisms. The Raman and Fourier transform infrared spectroscopy spectra verify the successful synthesis of the two modified nanofillers (f-GO and MTiO₂) and the formation of strong hydrogen bond within the PLA-starch nanocomposites. Due to the strong interfacial interaction and the synergistic effect from the combination of 1% MTiO₂ and 0.2% f-GO, obvious improvement was observed in PLA-starch versus other nanocomposites in terms of morphology, thermal stability, surface hydrophobicity, storage modulus, ultraviolet-shielding capacity, and aging-resistance. Furthermore, differential scanning calorimeter (DSC), isothermal crystallization kinetic, and X-ray diffraction analysis demonstrate that f-GO and the M-TiO₂ significantly synergize in enhancing the crystallization rate and crystallinity of PLA/starch matrix. These results provide novel insights for constructing high-performance nanocomposites and facilitate their applications in food packaging.     

Recycling of multilayer packaging using a reversible cross-linking adhesive

Plastic-based multilayer packaging has an important function on the packaging market, but is currently not recyclable as the polymer layers used are usually thermodynamically immiscible. This work therefore follows the approach to prepare separable multilayer packaging using a packaging adhesive modified with thermally unstable adducts, and proposes a corresponding recycling process. For this purpose, typical multilayer structures (polyethylene (PE)// polyethylene terephtalate (PET), PET//aluminum, and PE//aluminum) were prepared by curing furan-/maleimide-functionalized polyurethane (PU)-prepolymers with a three-functional cross-linking agent. Adhesions of up to over 3N per 15 mm test specimen were measured or substrate failures of PET films were observed. However, heating in dimethylsulfoxide, the retro-Diels–Alder reaction takes place and the cross-linked adhesive turns thermoplastic and dissolves in the solvent. Thus, the laminate separates and the pure PE, PET, and aluminum foils can be recovered without any PU residue.     

纳米纤维素的疏水改性及应用研究进展

纳米纤维素作为一种性能优越的可再生纳米材料，应用前景极为广阔。然而，由于纳米纤维素结构上富含羟基，使其具有极强的亲水性，严重影响了纳米纤维素的疏水性能，并且在一定程度上限制了其在复合材料领域的应用。综述了纳米纤维素疏水改性的研究进展，从物理吸附、表面化学修饰（甲硅烷化、烷酰化、酯化等）、聚合物接枝共聚3个方面简述了目前应用较为广泛的疏水化改性方法，并对疏水纳米纤维素在包装材料、造纸、水净化等方面的应用现状进行了总结。最后对疏水改性纳米纤维素的未来发展进行了展望，旨在为疏水纳米纤维素的研究和应用提供参考。     

浅析医药包装

随着市场经济的深入，医药包装正成为我国经济发展的朝阳产业，文中意在介绍先进的医药包装材料。分析其应用情况及发展趋势和动态。